Cobra MPC SERIES Manuale Utente Scaricare il pdf (Pagina 9)

SPECIAL PROGRAMMING SECTION:

CREATING THE PROGRAM CODE

The Program Code is the pass-

word used to change program-

ming. The program code is stored in address “00”.

1. Remove the battery access cover to gain access to the “PRGM” button.

2. Press “PRGM” button.

3. Yellow light on keypad will ﬂash rapidly indicating program mode.

While in the program mode, yellow light will continue to ﬂash until exit the pro-

gram mode or after a 30-second timeout period where there is no keystroke.

4. Press “00” for program code address.

5. Enter new 5 - 7 digit Program Code within 5 seconds.

6. When new Program Code is entered, wait for the red light to ﬂash twice

conﬁrming valid entry. A long red ﬂash indicates an error.

SET USER CODES

User codes are stored in addresses “01” through “55”. SABL must be in Pro-

gram Mode to add or delete User Codes.

1. Enter Program Code.

2. Press “E” button.

3. Yellow keypad light will ﬂash rapidly indicating program mode.

4. Press two digit preﬁx for new User Code address.

5. Enter new 1- 7 digit User Code within 5 seconds.

6. Wait for red light to ﬂash twice to conﬁrm valid entry.

7. Press “E” to exit program mode.

To delete individual user codes, enter “79” then any User Code.

To delete all users codes, enter “88” (not program or hard code).

PASSAGE CODES OR LOCKOUT CODES

The passage codes are stored in addresses “56” and “57”. Lockout codes are

stored in addresses “58” and “59”.

1. Enter Program Code.

2. Press the “E” button.

3. Yellow keypad light will ﬂash rapidly indicating program mode.

4. Enter “56” for passage code or “58” for lockout code within 5 seconds.

5. When desired code is entered, wait for red light to ﬂash twice conﬁrming

valid entry.

6. Press “E” to exit program mode.

To reverse passage or lockout code: Repeat above steps entering “57” to

exit passage or “59” to exit lockout code within 5 sec. Red light ﬂashES twice

conﬁrming valid entry. Press “E” to exit program mode.

RESET TO FACTORY DEFAULT, MASTER CODE UNKNOWN:

Press “HARD” button on CPU board for 1 second

Flashing yellow LED. Press “E” key until ﬂashing stops

Conﬁrm two (2) red ﬂashes. Press the “PRGM” buttonon CPU board for

one second. Conﬁrm ﬂashing yellow LED

Enter 0-0 followed by “E” key. Conﬁrm two (2) red ﬂashes.

Enter 8-8 followed by “E” key. Conﬁrm two (2) red ﬂashes.

Enter 8-9 followed by “E” key. Conﬁrm two (2) red ﬂashes.

Press the “E” key to end yellow ﬂashing LED.

Lock is back to default values

SECURITRON SABL

Categories Securitron SABL

ANSI/BHMA A156.2

Cylindrical Lock

Grade 1

UL/ULC fire rating 3-hour ‘A’ Label doors

Clutched Lever Clutched Exterior Lever

Available as Cylindrical Lock

Lever Handing Non-handed

(field reversible) Yes

Key Override Yes

Optional No

Keypad Layout 11 buttons, 1-0 and “E”

Button Construction EPDM rubber keys

Code Hierarchy Program Code, User

Codes

Master Code Program Code

Number Of Digits 5-7, only for

programming

Factory Default

Master

Created Program

Code is stored at

address “00”. Must

press “PRGM” button

adjacent to batteries

Sub-master Codes n/a

User Codes no. up to 55, 2-7 digits

Single use code n/a

Successful Code

Entry (lock/

unlocked)

Flash once per second

red LED. Can be

reversed to green LED

Levels of access Code Required,

Passage, Lock-out

Lock-out Override User locations 58 and

59. Code required to

enter and exit Lock-out

Anti-Tamper After 16 wrong digits

entered, keypad will

lock for 15 seconds,

beeper sounds

continuously

Weatherized Fully sealed exterior

electronics

Battery Life Over 100,000 cycles

Low Batteries

Warning

Two short beeps and

flash of LEDs at first

keystroke. Second, two

short beeps and LED

flash at each keystroke

Batteries 6 AA Alkaline

Battery Location Inside battery cover,

3/32” hex (Allen)

wrench

Replacement Non-volatile EEPROM

memory, no time

limitation

56 — LOCKSMITH LEDGER [11/10] www.locksmithledger.com

1 2 3 4 5 6 7 8 9 10

Commenti su questo manuale

Nessun commento

Cobra MPC SERIES Manuale Utente Pagina 9

Commenti su questo manuale